Aluminium Welding & Fabrication

If aluminium welding, fabrication and repairs are what you need then you have come to the right place. While we do focus on marine, boat, caravan and 4×4 accessories. You will be happy to know that we can also look after any aluminium fabrication requirements you may have. In addition to the above the other products we cover include aluminium canopies, canopy accessories, caravan storage boxes & accessories, aluminium toolbox. Aluminium boat repairs & refurbishment, including bow & hand rails.

We are based in Goolwa just a short drive from Victor Harbor & Port Elliot. When you are heading down to Goolwa Beach for a 4wd, or to fish the South Coast then Contact Us.

We also have a fully equipped mobile welding and maintenance vehicle available to mobilise to your premises if needed.

Custom Aluminium Canopy

Our Aluminium Canopies can be fully customised, and this tradesman canopy was built using 3mm aluminium plate and custom fitted to a 12ft Trailer. Reinforced gullwing side and rear access doors were a requirement, because of the harsh road conditions the trailer may encounter.

Aluminium TIG welding was used for most of the aluminium welding. With MIG welding carried out on the inner frames.

We used “Wattyl Macropoxy 250” for the undercoat and “Wattyl Polu-400” paint was used for the topcoat. The colour selected is Flat Black.

In addition we installed quality UES hardware that included compression locks, gas struts and extruded “Centaflex” continuous hinges.

Future improvements include manufacturing and fitting an aluminium Toolbox to each side of the wheel arches for tiedowns & aluminium tool storage. Internal shelving will also be added to the inside of the canopy, similar to what’s found in caravan storage boxes and 4×4 canopies.

Aluminium-TIG-Welding-Goolwa-1
Aluminium-Trailer-Canopy-Frame-3
Aluminium-Trailer-Canopy-Frame-1
Aluminium-Trailer-Canopy-Frame-2
Aluminium-Brackets
Aluminium-Trailer-Canopy
Aluminium-Trailer-Canopy-Frame-4
Aluminium-Trailer-Canopy-2
Aluminium-Trailer-Canopy-4
Aluminium-Trailer-Canopy-1
Aluminium-Trailer-Canopy-3
Aluminium-TIG-Welding
Aluminium-Canopy
Aluminium-Canopy-1
Aluminium-Canopy-5
Aluminium-Canopy-2
Aluminium-Canopy-3
Aluminium-Canopy-4
Aluminium-Canopy-6

Alumunium Boat Refurbishment – Stacer 626

This boat had a complete boat rebuild by us that included hardtop, new dash outboard pod and new bow and hand rails. The boat was built in the late 80’s, so it was no surprise that after an inspection of the hull. We had had to carry out some minor aluminium repairs, and the Aluminium welding method we used for the boat repairs was TIG.

The boat accessories needed extensive aluminium tube and plate bending and in addition new seat boxes, live bait tank and fuel tank were fabricated.

Before:

  • Aluminium Repair
    Stacer 626 before rebuild

After:

Rebuild & Fabrication stage:

Aluminium Welding and Fabrication – Stacer 626

  • Aluminium Hardtop
  • Bow and hand rails
  • Rocket launches and rod holders
  • Transom mounted live bait tank
  • Axillary motor pod
  • Dive Ladder
  • Aluminium fuel tank
  • Aluminium TIG welding
  • Aluminium Welding
  • Aluminium Welding
  • Aluminium Welding
  • Aluminium Fabrication
  • Aluminium Fabrication
  • Aluminium Fabrication
  • Aluminium Welding
  • Aluminium Fabrication
  • Aluminium Welding Goolwa

14ft Aluminium Boat

The customer requested a high aluminium bow rails, bow roller and gunwale rails. The 14ft tinny came in without any rails and was not very easy to handle when launching and retrieving on the metro beaches south of Adelaide.

  • Custom bow Rail using 25mm x 3mm aluminium tube.
  • Navigational light plates fitted to bow rail.
  • Fully customised and designed bow roller. 5mm plate and 12mm stainless steel bolts.
  • Gunwale rails using 25mm x 3mm aluminium tube.
  • Fully Tig welded design.